4. Installing the AX.25/NET/ROM/ROSE software

4.1. Compiling the kernel

If you are already familiar with the process of compiling the Linux kernel then you can skip this section, just be sure to select the appropriate options when compiling the kernel. If you are not, then read on. You may also want to read the Linux Kernel HOWTO.

The normal place for the kernel source to be unpacked to is the /usr/src directory into a subdirectory called linux. To do this you should be logged in as root and execute a series of commands similar to the following:

# cd /usr/src # mv linux linux.old # tar xzvf linux-2.4.9.tar.gz # cd linux

After you have unpacked the kernel source, you need to run the configuration script and choose the options that suit your hardware configuration and the options that you wish built into your kernel. You do this by using the command:

# make menuconfig

If you are running X you can get a graphical interface using:

# make xconfig

You might also try:

# make config

I'm going to describe the full screen method (menuconfig) because it is easier to move around, but use whichever you are most comfortable with.

In either case you will be offered a range of options at which you must answer `Y' or `N'. (Note you may also answer `M' if you are using modules. For the sake of simplicity I will assume you are not, please make appropriate modifications if you are).

The options most relevant to an AX.25 configuration are:

Code maturity level options ---> [*] Prompt for development and/or incomplete code/drivers ... General setup ---> ... [*] Networking support ... Networking options ---> <*> UNIX domain sockets ... [*] TCP/IP networking ... [?] IP: tunneling ... Amateur Radio Support ---> --- Packet Radio protocols [*] Amateur Radio AX.25 Level 2 protocol [?] AX.25 DAMA Slave support [?] Amateur Radio NET/ROM protocol [?] Amateur Radio X.25 PLP (Rose) AX.25 network device drivers ---> <?> Serial port KISS driver <?> Serial port 6PACK driver <?> BPQ Ethernet driver <?> High-speed (DMA) SCC driver for AX.25 <?> Z8530 SCC driver <?> BAYCOM ser12 fullduplex driver for AX.25 <?> BAYCOM ser12 halfduplex driver for AX.25 <?> BAYCOM picpar and par96 driver for AX.25 <?> BAYCOM epp driver for AX.25 <?> Soundcard modem driver [?] soundmodem support for Soundblaster and compatible cards [?] soundmodem support for WSS and Crystal cards [?] soundmodem support for 1200 baud AFSK modulation [?] soundmodem support for 2400 baud AFSK modulation (7.3728MHz crystal) [?] soundmodem support for 2400 baud AFSK modulation (8MHz crystal) [?] soundmodem support for 2666 baud AFSK modulation [?] soundmodem support for 4800 baud HAPN-1 modulation [?] soundmodem support for 4800 baud PSK modulation [?] soundmodem support for 9600 baud FSK G3RUH modulation <?> YAM driver for AX.25

The options I have flagged with a `*' are those that you must must answer `Y' to. The rest are dependent on what hardware you have and what other options you want to include. Some of these options are described in more detail later on, so if you don't know what you want yet, then read ahead and come back to this step later.

After you have completed the kernel configuration you should be able to cleanly compile your new kernel:

# make dep # make clean # make zImage

Make sure you move your arch/i386/boot/zImage file wherever you want it and then edit your /etc/lilo.conf file and rerun lilo to ensure that you actually boot from it.

4.1.1. A word about kernel modules

Compiling drivers as modules is useful if you only use AX.25 occasionally and want to be able to load and unload them on demand to save system resources. However, some people have problems getting the modularized drivers working because they are more complicated to configure. If you've chosen to compile any drivers as modules, then you'll also need to run the commands:

# make modules # make modules_install

to install your modules in the appropriate location.

You will also need to add some entries into your /etc/modules.conf file to ensure that the kerneld program knows how to locate the kernel modules. You should add/modify the following:

alias net-pf-3 ax25 alias net-pf-6 netrom alias net-pf-11 rose alias tty-ldisc-1 slip alias tty-ldisc-3 ppp alias tty-ldisc-5 mkiss alias bc0 baycom alias nr0 netrom alias pi0a pi2 alias pt0a pt alias scc0 optoscc (or one of the other scc drivers) alias sm0 soundmodem alias tunl0 newtunnel alias char-major-4 serial alias char-major-5 serial alias char-major-6 lp

On Debian-based Linux systems these entries should go into the file /etc/modutils/aliases and then you need to run /sbin/update-mpodules.

4.2. The AX.25 library, tools, and application programs

After you have successfully compiled and booted your new kernel you need to compile and install the ax25 library, tools, and application programs.

To compile and install libax25 you should use a series of commands similar to the following:

# cd /usr/src # tar xzvf libax25-0.0.7.tar.gz # cd libax25-0.0.7 # ./configure --exec_prefix=/usr --sysconfdir=/etc --localstatedir=/var # make # make install

The arguments to the configure command ensure that the files will be installed in the "standard" places under the directory /usr in subdirectories bin, sbin, etc and man. If you simply run configure with no options it will default to putting all files under /usr/local. This can cause the situation where you have configuration files in both /usr and /usr/local. If you want to ensure that this can't happen you can make /usr/local/etc/ax25 a symbolic link to /etc/ax25 at the very beginning of the install process and then you won't have to worry about it.

If this is a first time installation, that is you've never installed any ax25 code on your machine before, you should also use the:

# make installconf

command to install some sample configuration files into the /etc/ax25/ directory from which to work.

You can now build install the AX.25 tools in a similar fashion:

# cd /usr/src # tar xzvf ax25-tools-0.0.6.tar.gz # cd ax25-tools-0.0.6 # ./configure --prefix=/usr --sysconfdir=/etc --localstatedir=/var # make # make install # make installconf (if you want to install the configuration files)

And finally you can install the AX.25 applications:

# cd /usr/src # tar xzvf ax25-apps-0.0.4.tar.gz # cd ax25-apps-0.0.4 # ./configure --prefix=/usr --sysconfdir=/etc --localstatedir=/var # make # make install # make installconf (if you want to install the configuration files)

If you get messages something like:

gcc -Wall -Wstrict-prototypes -O2 -I../lib -c call.c call.c: In function `statline': call.c:268: warning: implicit declaration of function `attron' call.c:268: `A_REVERSE' undeclared (first use this function) call.c:268: (Each undeclared identifier is reported only once call.c:268: for each function it appears in.)

then you should double check that you have the ncurses package properly installed on your system. The configuration script attempts to locate your package in the common locations, but some installations have it badly installed and it is unable to locate them.